This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
howto:solaris:install [2012/01/18 12:15] n3mmr |
howto:solaris:install [2012/01/29 12:13] n3mmr |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | The below procedure installs | + | ====== How to install |
- | It will likely work just as well, with possibly minor details changed, on Solaris | + | |
+ | === Note that, Solaris or OpenIndiana or any other Solaris descendant, is NOT Linux === | ||
+ | <fc # | ||
+ | Most of the visible differences occur in admin software, but a few quirks exist in userland, too. | ||
+ | And the package system is aggressively different. | ||
+ | Still, most any Java library is likely to run w/o any problem, and most Linux software | ||
+ | can be automatically transformed to run in Solaris descendants. | ||
+ | And, given its heritage, Solaris makes for very good and reliable servers. //</ | ||
+ | |||
+ | The below procedure installs serviio as a service under SMF in Openindiana v 151a and later. | ||
+ | It will likely work just as well, with possibly minor details changed, on Solaris 10 or 11, Nexenta and OpenSolaris b134 (possibly earlier versions too). | ||
- | First, make sure you have the appropriate supporting SW installed: | + | The serviio console should normally be started from a separate copy of serviio, given the below setup. |
+ | In most useful cases, this is anyway the case, since you want serviio running on a server machine, and you run the console from another machine, say your laptop. | ||
+ | **First, make sure you have the appropriate supporting SW installed: | ||
ffmpeg 0.9.1 with rtmp-support, | ffmpeg 0.9.1 with rtmp-support, | ||
http:// | http:// | ||
- | from where you can install using the IPS installer, pkg, of your openindiana | + | from where you can install using the IPS installer, pkg, of your OpenIndiana |
- | Then get the linux tar distro, and extract | + | **Get the distro and install |
- | Now test it by running it manually: | + | Download the serviio linux tar distro, and extract |
- | prompt> cd / | + | Create a group " |
+ | |||
+ | **//<fc # | ||
+ | |||
+ | and a user " | ||
+ | |||
+ | **//<fc # | ||
+ | |||
+ | On my system, 103 was free in both cases, and one might as well use the same number for both. | ||
+ | |||
+ | Now, make sure the / | ||
+ | **//<fc # | ||
+ | prompt> cd /usr/local; chown -R serviio: | ||
+ | //** | ||
+ | |||
+ | Now test it by running it manually, as user serviio: | ||
+ | |||
+ | <fc # | ||
+ | **//<fc #0000FF>prompt> cd / | ||
+ | </ | ||
+ | **//<fc #0000FF> | ||
prompt> ./ | prompt> ./ | ||
- | prompt> ./ | + | </ |
+ | **//<fc # | ||
+ | prompt> ./ | ||
Enter the correct address to bind to explicitly on the Status panel, and save. | Enter the correct address to bind to explicitly on the Status panel, and save. | ||
Line 27: | Line 60: | ||
Make sure serviio is stopped! | Make sure serviio is stopped! | ||
- | Now create | + | **Lastly, define |
- | + | ||
- | prompt> groupadd -g 103 serviio | + | |
- | + | ||
- | and a user " | + | |
- | + | ||
- | prompt> useradd -u 103 -g 103 -d / | + | |
- | + | ||
- | On my system, 103 was free in both cases, and one might as well use the same number for both. | + | |
- | + | ||
- | Now, make sure the / | + | |
- | + | ||
- | prompt> cd /usr/local; chown -R serviio: | + | |
- | + | ||
Save the xml text found at the end of this page in a file " | Save the xml text found at the end of this page in a file " | ||
- | + | **// | |
- | prompt> pfexec svccfg validate ~serviio/ | + | <fc #0000FF>prompt> pfexec svccfg validate ~serviio/ |
- | prompt> pfexec svccfg import ~serviio/ | + | </ |
+ | **//<fc #0000FF> | ||
+ | prompt> pfexec svccfg import ~serviio/ | ||
This creates a new service svc:/ | This creates a new service svc:/ | ||
Line 51: | Line 72: | ||
Next enable the service, so that it will start up whenever the machine is booted, and will be restarted if it gets shot down by mistake. | Next enable the service, so that it will start up whenever the machine is booted, and will be restarted if it gets shot down by mistake. | ||
- | prompt> svcadm enable serviio | + | **//<fc #0000FF>prompt> |
+ | </ | ||
- | and as you can see, one needs not use the full fmri, as long as you use enough of the name to make it unique. | + | You can look at the serviio service by doing |
+ | ** | ||
+ | //<fc # | ||
+ | and as you can see, you need not use the full fmri, as long as you use enough of the name to make it unique. | ||
+ | As a final check, just in case, look at / | ||
+ | This might be wrong if you had an earlier copy running as some user other than serviio, or you did the manual test above not as user serviio. | ||
+ | |||
+ | < | ||
---------serviio.xml file contents------------ | ---------serviio.xml file contents------------ | ||
+ | |||
<?xml version=" | <?xml version=" | ||
< | < | ||
Line 76: | Line 106: | ||
< | < | ||
</ | </ | ||
- | |||
- | |||
- | | ||
- | | ||
- | | ||
| | ||
< | < | ||
Line 92: | Line 117: | ||
< | < | ||
<propval name=" | <propval name=" | ||
- | | ||
- | | ||
<propval name=" | <propval name=" | ||
</ | </ | ||
Line 100: | Line 123: | ||
| | ||
</ | </ | ||
- | | ||
| | ||
< | < | ||
Line 116: | Line 138: | ||
</ | </ | ||
-------end of serviio.xml contents--------------- | -------end of serviio.xml contents--------------- | ||
+ | </ |